1

介紹

本文介紹由e2 studio自動生成的FSP LVGL pack的使用說明，Pack的生成方法可以參考前面的介紹文章。用戶可以通過添加該pack，以可視化的形式添加和配置Little VGL，包括Little VGL的分辨率、色深、DPI以及官方的demo等進行配置。用戶不用再做移植Little VGL的源代碼，不用再繁瑣的添加各個頭文件。本次實驗所用硬件為EK-RA8D1，如下圖。確保板子的SW1-7切換到“ON”

2

軟件架構

通過pack生成的代碼主要在ra→fsp→src→rm_lvgl_prot和ra→lvgl兩個路徑下

3

安裝教程

1

打開e2 studio菜單中“File”→“Import... ”

2

在彈出的“Import”對話框中，選擇“General”→“CMSIS Pack”，點擊“Next”

3

在彈出的“Import CMSIS Pack”對話框中，點擊“Specify pack file”右側“...”，指定需要添加的pack文件

4

“Specify device family”選擇“RA”，點擊Finish

4

使用說明

1

重新打開e2 studio

2

新建工程，新建工程步驟不再贅述，F(xiàn)SP版本選擇5.1.0及以上，Board選擇EK-RA8D1

3

新建好工程后，添加LVGL的stack，這時候會提示GLCDC的時鐘沒有打開，切換到clocks選項卡，enable LCD的clock，選擇PLL1P，讓LCD時鐘輸出為240MHz即可。

添加MIPI DSI driver，左鍵點擊Add MIPI DSI Output(Optional)→New→MIPI Display(r_mipi_dsi):

NOTE

Enable LCD的clock后，r_glcdc的紅色提示會消失。

修改LVGL顯示分辨率：480*854，enable 2D

使能touch

修改glcdc的名字為g_display_lvgl：

4

添加2D驅動，如果上述步驟沒有enable 2D，此步驟可以跳過。New Stack→Graphics→D/AVE 2D Port Interface

添加完2D stack后，在BSP選項卡中heap給2D使用，同時加大stack的值為0x2000：

5

添加I2C驅動

修改I2C的配置，Name: g_i2c_master1, Channel: 1, Slave address: 0x5D, Callback: g_i2c_master1_cb, Interrupt Priority Level：Priority 12

6

添加GPIO中斷，修改irq的配置：Name：g_external_irq3，Channel：3，Callback：touch_irq_cb

P510設為input模式，IRQ選擇為IRQ3

7

配置引腳，改變SDRAM的引腳驅動能力：PA00 -- H， PA08 -- H， PA09 -- HH， PA10 -- H， P404設為輸出模式，初始化為高電平，PA01設為輸出模式，初始化為高電平

8

點擊Generate Project Content，生成代碼

9

添加應用代碼，做一個LVGL下拉控件。修改 hal_entry.c如下：

左右滑動查看完整代碼內容

#include "hal_data.h"
#include "dsi_layer.h"
#include "lvgl.h"
#include "lv_demos.h"


FSP_CPP_HEADER
void R_BSP_WarmStart(bsp_warm_start_event_t event);
FSP_CPP_FOOTER




#define RGB_565_REG  (0x1F << 11)
#define RGB_565_GREEN ?(0x3F << 5)
#define RGB_565_BLUE ? (0x1F << 0)


/* Global variable to keep track of requested application */
void SysTick_Handler(void);


#define LVGL_TICK_MS 1U
static volatile uint32_t s_tick ? ? ? ?= 0U;
static volatile bool s_lvglTaskPending = false;
#define LVGL_TASK_PERIOD_TICK 3U
static void DEMO_SetupTick(void)
{
if (0 != SysTick_Config(SystemCoreClock / (LVGL_TICK_MS * 1000U)))
{
while (1)
;
}
}


void SysTick_Handler(void)
{
s_tick++;
lv_tick_inc(LVGL_TICK_MS);


if ((s_tick % LVGL_TASK_PERIOD_TICK) == 0U)
{
s_lvglTaskPending = true;
}
}


#if LV_BUILD_EXAMPLES


static void event_handler(lv_event_t * e)
{
lv_event_code_t code = lv_event_get_code(e);
lv_obj_t * obj = lv_event_get_target(e);
if(code == LV_EVENT_VALUE_CHANGED) {
char buf[32];
lv_dropdown_get_selected_str(obj, buf, sizeof(buf));
LV_LOG_USER("Option: %s", buf);
}
}


void lv_example_dropdown_1(void)
{


/*Create a normal drop down list*/
lv_obj_t * dd = lv_dropdown_create(lv_scr_act());
lv_dropdown_set_options(dd, "Apple
"
"Banana
"
"Orange
"
"Cherry
"
"Grape
"
"Raspberry
"
"Melon
"
"Orange
"
"Lemon
"
"Nuts");


lv_obj_align(dd, LV_ALIGN_TOP_MID, 0, 20);
lv_obj_add_event_cb(dd, event_handler, LV_EVENT_ALL, NULL);
}
#endif


/*******************************************************************************************************************//**
main() is generated by the RA Configuration editor and is used to generate threads if an RTOS is used. ?This function
is called by main() when no RTOS is used.
**********************************************************************************************************************/
void hal_entry(void)
{


/* TODO: add your own code here */
fsp_err_t ?err;
/* Fill the Frame buffer with Blue, to zero out info from previous execution runs */
uint32_t count;


uint16_t * p = (uint16_t *)&fb_background[0][0];
for (count = 0; count < sizeof(fb_background)/2; count++)
{
*p++ = RGB_565_REG;
}


DEMO_SetupTick();
lv_init();


lv_port_disp_init();
#if Touch_Enable
lv_port_indev_init();
#endif


lv_example_dropdown_1();
#if LV_USE_DEMO_WIDGETS
// ? ? ? lv_demo_widgets();
#endif


#if LV_USE_DEMO_STRESS
lv_demo_stress();
#endif
#if LV_USE_DEMO_BENCHMARK
lv_demo_benchmark();
#endif
#if LV_USE_DEMO_MUSIC
lv_demo_music();
#endif
// ? ?lv_task_handler();
/* handle the tasks of LVGL */
while(1)
{
while (!s_lvglTaskPending)
{
}
s_lvglTaskPending = false;
lv_task_handler();
}






#if BSP_TZ_SECURE_BUILD
/* Enter non-secure code */
R_BSP_NonSecureEnter();
#endif
}


/*******************************************************************************************************************//**
This function is called at various points during the startup process. ?This implementation uses the event that is
called right before main() to set up the pins.
*
* @param[in] ?event ? ?Where at in the start up process the code is currently at
**********************************************************************************************************************/
void R_BSP_WarmStart(bsp_warm_start_event_t event)
{
if (BSP_WARM_START_RESET == event)
{
#if BSP_FEATURE_FLASH_LP_VERSION != 0


/* Enable reading from data flash. */
R_FACI_LP→DFLCTL = 1U;


/* Would normally have to wait tDSTOP(6us) for data flash recovery. Placing the enable here, before clock and
C runtime initialization, should negate the need for a delay since the initialization will typically take more than 6us. */
#endif
}


if (BSP_WARM_START_POST_C == event)
{
/* C runtime environment and system clocks are setup. */


/* Configure pins. */
R_IOPORT_Open (&g_ioport_ctrl, &IOPORT_CFG_NAME);


bsp_sdram_init(); //SDRAM pins need to be set to HIGH drive strength in pin configuration
}
}


#if BSP_TZ_SECURE_BUILD


FSP_CPP_HEADER
BSP_CMSE_NONSECURE_ENTRY void template_nonsecure_callable ();


/* Trustzone Secure Projects require at least one nonsecure callable function in order to build (Remove this if it is not required to build). */
BSP_CMSE_NONSECURE_ENTRY void template_nonsecure_callable ()
{


}
FSP_CPP_FOOTER


#endif

10

編譯，下載到EK-RA8D1，連接MIPI屏，會得到以下結果：

至此，已經完成LVGL的移植以及測試。下面我們直接配置FSP，把官方的demo使能起來：打開configuration.xml,配置如下：

配置完成后，點擊Generate Project Content。修改hal_entry.c:

 #include "hal_data.h"
 #include "dsi_layer.h"
 #include "lvgl.h"
 #include "lv_demos.h"


 FSP_CPP_HEADER
 void R_BSP_WarmStart(bsp_warm_start_event_t event);
 FSP_CPP_FOOTER




 #define RGB_565_REG  (0x1F << 11)
 #define RGB_565_GREEN ?(0x3F << 5)
 #define RGB_565_BLUE ? (0x1F << 0)


 /* Global variable to keep track of requested application */
 void SysTick_Handler(void);


 #define LVGL_TICK_MS 1U
 static volatile uint32_t s_tick ? ? ? ?= 0U;
 static volatile bool s_lvglTaskPending = false;
 #define LVGL_TASK_PERIOD_TICK 3U
 static void DEMO_SetupTick(void)
{
 ? ?if (0 != SysTick_Config(SystemCoreClock / (LVGL_TICK_MS * 1000U)))
 ? ?{
 ? ? ? ?while (1)
 ? ? ? ? ? ?;
 ? ?}
 }


 void SysTick_Handler(void)
{
 ? ?s_tick++;
 ? ?lv_tick_inc(LVGL_TICK_MS);


 ? ?if ((s_tick % LVGL_TASK_PERIOD_TICK) == 0U)
 ? ?{
 ? ? ? ?s_lvglTaskPending = true;
 ? ?}
 }


 #if LV_BUILD_EXAMPLES


 static void event_handler(lv_event_t * e)
{
 ? ?lv_event_code_t code = lv_event_get_code(e);
 ? ?lv_obj_t * obj = lv_event_get_target(e);
 ? ?if(code == LV_EVENT_VALUE_CHANGED) {
 ? ? ? ?char buf[32];
 ? ? ? ?lv_dropdown_get_selected_str(obj, buf, sizeof(buf));
 ? ? ? ?LV_LOG_USER("Option: %s", buf);
 ? ?}
 }


 void lv_example_dropdown_1(void)
{


 ? ?/*Create a normal drop down list*/
 ? ?lv_obj_t * dd = lv_dropdown_create(lv_scr_act());
 ? ?lv_dropdown_set_options(dd, "Apple
"
 ? ? ? ? ? ? ? ? ? ? ? ? ? ?"Banana
"
 ? ? ? ? ? ? ? ? ? ? ? ? ? ?"Orange
"
 ? ? ? ? ? ? ? ? ? ? ? ? ? ?"Cherry
"
 ? ? ? ? ? ? ? ? ? ? ? ? ? ?"Grape
"
 ? ? ? ? ? ? ? ? ? ? ? ? ? ?"Raspberry
"
 ? ? ? ? ? ? ? ? ? ? ? ? ? ?"Melon
"
 ? ? ? ? ? ? ? ? ? ? ? ? ? ?"Orange
"
 ? ? ? ? ? ? ? ? ? ? ? ? ? ?"Lemon
"
 ? ? ? ? ? ? ? ? ? ? ? ? ? ?"Nuts");


 ? ?lv_obj_align(dd, LV_ALIGN_TOP_MID, 0, 20);
 ? ?lv_obj_add_event_cb(dd, event_handler, LV_EVENT_ALL, NULL);
 }
 #endif


 /*******************************************************************************************************************//**
 ?* main() is generated by the RA Configuration editor and is used to generate threads if an RTOS is used. ?This function
 ?* is called by main() when no RTOS is used.
 ?**********************************************************************************************************************/
 void hal_entry(void)
{


 ? ?/* TODO: add your own code here */
 ? ?fsp_err_t ?err;
 ? ?/* Fill the Frame buffer with Blue, to zero out info from previous execution runs */
 ? ?uint32_t count;


 ? ?uint16_t * p = (uint16_t *)&fb_background[0][0];
 ? ?for (count = 0; count < sizeof(fb_background)/2; count++)
 ? ?{
 ? ? ? ?*p++ = RGB_565_REG;
 ? ?}


 ? ?DEMO_SetupTick(); //為lvgl提供心跳
 ? ?lv_init(); 
 ? ?lv_port_disp_init();
 #if Touch_Enable
 ? ?lv_port_indev_init();
 #endif


 // ? ? ? lv_example_dropdown_1();
 #if LV_USE_DEMO_WIDGETS
 ? ?lv_demo_widgets();
 #endif


 #if LV_USE_DEMO_STRESS
 ? ?lv_demo_stress();
 #endif
 #if LV_USE_DEMO_BENCHMARK
 ? ?lv_demo_benchmark();
 #endif
 #if LV_USE_DEMO_MUSIC
 ? ?lv_demo_music();
 #endif
 // ? ?lv_task_handler();
 ? ?/* handle the tasks of LVGL */
 ? ?while(1)
 ? ?{
 ? ? ? ?while (!s_lvglTaskPending)
 ? ? ? ?{
 ? ? ? ?}
 ? ? ? ?s_lvglTaskPending = false;
 ? ? ? ?lv_task_handler();
 ? ?}






 #if BSP_TZ_SECURE_BUILD
 ? ?/* Enter non-secure code */
 ? ?R_BSP_NonSecureEnter();
 #endif
 }


 ? ?/*******************************************************************************************************************//**
 ? ?* This function is called at various points during the startup process. ?This implementation uses the event that is
 ? ?* called right before main() to set up the pins.
 ? ?*
 ? ?* @param[in] ?event ? ?Where at in the start up process the code is currently at
 ? ?**********************************************************************************************************************/
 ? ?void R_BSP_WarmStart(bsp_warm_start_event_t event)
{
 ? ? ? ?if (BSP_WARM_START_RESET == event)
 ? ? ? ?{
 ? ?#if BSP_FEATURE_FLASH_LP_VERSION != 0


 ? ? ? ? ? ?/* Enable reading from data flash. */
 ? ? ? ? ? ?R_FACI_LP→DFLCTL = 1U;


 ? ? ? ? ? ?/* Would normally have to wait tDSTOP(6us) for data flash recovery. Placing the enable here, before clock and
 ? ? ? ? ? ?* C runtime initialization, should negate the need for a delay since the initialization will typically take more than 6us. */
 ? ?#endif
 ? ? ? ?}


 ? ? ? ?if (BSP_WARM_START_POST_C == event)
 ? ? ? ?{
 ? ? ? ? ? ?/* C runtime environment and system clocks are setup. */


 ? ? ? ? ? ?/* Configure pins. */
 ? ? ? ? ? ?R_IOPORT_Open (&g_ioport_ctrl, &IOPORT_CFG_NAME);


 ? ? ? ? ? ?bsp_sdram_init(); //SDRAM pins need to be set to HIGH drive strength in pin configuration
 ? ? ? ?}
 ? ?}


 ? ?#if BSP_TZ_SECURE_BUILD


 ? ?FSP_CPP_HEADER
 ? ?BSP_CMSE_NONSECURE_ENTRY void template_nonsecure_callable ();


 ? ?/* Trustzone Secure Projects require at least one nonsecure callable function in order to build (Remove this if it is not required to build). */
 ? ?BSP_CMSE_NONSECURE_ENTRY void template_nonsecure_callable ()
{


 ? ?}
 ? ?FSP_CPP_FOOTER


 ? ?#endif

編譯，下載。得到結果如下：

如果實驗過程有問題，可以下載本倉庫中e2studio_project下的RA8D1_simple_demo和RA8D1_widgets_demo兩個完整的工程做對比。

基于RA8D1的LVGL FSP配置以及使用已經介紹完畢。

審核編輯：劉清