//RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB|RCC_APB2Periph_GPIOC|RCC_APB2Periph_GPIOD|RCC_APB2Periph_GPIOE|RCC_APB2Periph_GPIOG|RCC_APB2Periph_AFIO,ENABLE);//ê1?üPORTB,D,E,Gò??°AFIO?′ó?1|?üê±?ó

/*Configure GPIO pin : PC5 */

GPIO_InitStruct.Pin = GPIO_PIN_5;

GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;

GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_MEDIUM;

HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);

/*Configure GPIO pin : PB0 */

GPIO_InitStruct.Pin = GPIO_PIN_0;

GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;

GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_MEDIUM;

HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);

/* GPIO_InitStruct */

GPIO_InitStruct.Pin = GPIO_PIN_0|GPIO_PIN_12;

GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;

GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;

HAL_GPIO_Init(GPIOG, &GPIO_InitStruct);

/* GPIO_InitStruct */

GPIO_InitStruct.Pin = GPIO_PIN_7|GPIO_PIN_8|GPIO_PIN_9|GPIO_PIN_10

|GPIO_PIN_11|GPIO_PIN_12|GPIO_PIN_13|GPIO_PIN_14

|GPIO_PIN_15;

GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;

GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;

HAL_GPIO_Init(GPIOE, &GPIO_InitStruct);

/* GPIO_InitStruct */

GPIO_InitStruct.Pin = GPIO_PIN_8|GPIO_PIN_9|GPIO_PIN_10|GPIO_PIN_14

|GPIO_PIN_15|GPIO_PIN_0|GPIO_PIN_1|GPIO_PIN_4

|GPIO_PIN_5;

GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;

GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;

HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);

readWriteTiming.AddressSetupTime = 0x01; //μ??·?¨á￠ê±??￡¨ADDSET￡??a2??HCLK 1/36M=27ns

readWriteTiming.AddressHoldTime = 0x00; //μ??·±￡3?ê±??￡¨ADDHLD￡??￡ê?A?′ó?μ?

readWriteTiming.DataSetupTime = 0x0f; // êy?Y±￡′?ê±???a16??HCLK,òò?aòo?§?y?ˉICμ??áêy?Yμ?ê±oò￡??ù?è2??üì??ì￡?óè????1289?a??IC?￡

readWriteTiming.BusTurnAroundDuration = 0x00;

readWriteTiming.CLKDivision = 0x00;

readWriteTiming.DataLatency = 0x00;

readWriteTiming.AccessMode = FSMC_ACCESS_MODE_A; //?￡ê?A

writeTiming.AddressSetupTime = 0x02; //0x01 μ??·?¨á￠ê±??￡¨ADDSET￡??a1??HCLK

writeTiming.AddressHoldTime = 0x00; //μ??·±￡3?ê±??￡¨A

writeTiming.DataSetupTime = 0x05; ////0x03 êy?Y±￡′?ê±???a4??HCLK

writeTiming.BusTurnAroundDuration = 0x00;

writeTiming.CLKDivision = 0x00;

writeTiming.DataLatency = 0x00;

writeTiming.AccessMode = FSMC_ACCESS_MODE_A; //?￡ê?A

hsram2.Init.NSBank = FSMC_NORSRAM_BANK4;//? ?aà??ò??ê1ó?NE4 ￡?ò2?í??ó|BTCR[6],[7]?￡

hsram2.Init.DataAddressMux = FSMC_DATA_ADDRESS_MUX_DISABLE; // 2??′ó?êy?Yμ??·

hsram2.Init.MemoryType =FSMC_MEMORY_TYPE_SRAM;// FSMC_MemoryType_SRAM;? //SRAM

hsram2.Init.MemoryDataWidth = FSMC_NORSRAM_MEM_BUS_WIDTH_16;//′?′￠?÷êy?Y?í?è?a16bit

hsram2.Init.BurstAccessMode =FSMC_BURST_ACCESS_MODE_DISABLE;// FSMC_BurstAccessMode_Disable;

hsram2.Init.WaitSignalPolarity = FSMC_WAIT_SIGNAL_POLARITY_LOW;

hsram2.Init.AsynchronousWait=FSMC_ASYNCHRONOUS_WAIT_DISABLE;

hsram2.Init.WrapMode = FSMC_WRAP_MODE_DISABLE;

hsram2.Init.WaitSignalActive = FSMC_WAIT_TIMING_BEFORE_WS;

hsram2.Init.WriteOperation = FSMC_WRITE_OPERATION_ENABLE; //? ′?′￠?÷D′ê1?ü

hsram2.Init.WaitSignal = FSMC_WAIT_SIGNAL_DISABLE;

hsram2.Init.ExtendedMode = FSMC_EXTENDED_MODE_ENABLE; // ?áD′ê1ó?2?í?μ?ê±Dò

hsram2.Init.WriteBurst = FSMC_WRITE_BURST_DISABLE;

//FSMC_NORSRAMInitStructure.FSMC_ReadWriteTimingStruct = &readWriteTiming; //?áD′ê±Dò

//FSMC_NORSRAMInitStructure.FSMC_WriteTimingStruct = &writeTiming;? //D′ê±Dò

if (HAL_SRAM_Init(&hsram2, &readWriteTiming, &writeTiming) != HAL_OK)

{

_Error_Handler(__FILE__, __LINE__);

}

__FSMC_NORSRAM_ENABLE(FSMC_NORSRAM_DEVICE,FSMC_NORSRAM_BANK4);

}

修改后的LCD初始化函數

void LCD_Init(void)

{

LCD_GPIOInit();

LCD_RESET();

//************* Start Initial Sequence **********//

LCD_WriteReg(0x00E5,0x78F0);

LCD_WriteReg(0x0001,0x0100);

LCD_WriteReg(0x0002,0x0700);

LCD_WriteReg(0x0003,0x1030);

LCD_WriteReg(0x0004,0x0000);

LCD_WriteReg(0x0008,0x0202);

LCD_WriteReg(0x0009,0x0000);

LCD_WriteReg(0x000A,0x0000);

LCD_WriteReg(0x000C,0x0000);

LCD_WriteReg(0x000D,0x0000);

LCD_WriteReg(0x000F,0x0000);

//power on sequence VGHVGL

LCD_WriteReg(0x0010,0x0000);

LCD_WriteReg(0x0011,0x0007);

LCD_WriteReg(0x0012,0x0000);

LCD_WriteReg(0x0013,0x0000);

LCD_WriteReg(0x0007,0x0000);

//vgh

LCD_WriteReg(0x0010,0x1690);

LCD_WriteReg(0x0011,0x0227);

//delay_ms(100);

//vregiout

LCD_WriteReg(0x0012,0x009D); //0x001b

//delay_ms(100);

//vom amplitude

LCD_WriteReg(0x0013,0x1900);

//delay_ms(100);

//vom H

LCD_WriteReg(0x0029,0x0025);

LCD_WriteReg(0x002B,0x000D);

//gamma

LCD_WriteReg(0x0030,0x0007);

LCD_WriteReg(0x0031,0x0303);

LCD_WriteReg(0x0032,0x0003);// 0006

LCD_WriteReg(0x0035,0x0206);

LCD_WriteReg(0x0036,0x0008);

LCD_WriteReg(0x0037,0x0406);

LCD_WriteReg(0x0038,0x0304);//0200

LCD_WriteReg(0x0039,0x0007);

LCD_WriteReg(0x003C,0x0602);// 0504

LCD_WriteReg(0x003D,0x0008);

//ram

LCD_WriteReg(0x0050,0x0000);

LCD_WriteReg(0x0051,0x00EF);

LCD_WriteReg(0x0052,0x0000);

LCD_WriteReg(0x0053,0x013F);

LCD_WriteReg(0x0060,0xA700);

LCD_WriteReg(0x0061,0x0001);

LCD_WriteReg(0x006A,0x0000);

//

LCD_WriteReg(0x0080,0x0000);

LCD_WriteReg(0x0081,0x0000);

LCD_WriteReg(0x0082,0x0000);

LCD_WriteReg(0x0083,0x0000);

LCD_WriteReg(0x0084,0x0000);

LCD_WriteReg(0x0085,0x0000);

//

LCD_WriteReg(0x0090,0x0010);

LCD_WriteReg(0x0092,0x0600);

LCD_WriteReg(0x0007,0x0133);

LCD_WriteReg(0x00,0x0022);//

LCD_SetParam();//éè??LCD2?êy

//LCD_LED=1;//μ?áá±31a

HAL_GPIO_WritePin(GPIOB, GPIO_PIN_0, GPIO_PIN_SET);

LCD_Clear(WHITE);

}

修改后在main函數中使用繪圖函數時要注釋掉原有的GPIO和FSMC初始化函數。

測試結果：

?

圖片發自簡書App

?

圖片發自簡書App

修改后即可以在STM32CubeMX中配置后就可以將之前修改好的文件直接添加到工程中使用，這樣即可在LCD上顯示其他功能的狀態信息。